Products : Tube Cleaning Accessories

Brushes  " - 1" I.D.

Nylon Brushes
Used for removing soft scales in ferrous tubes (carbon steel, stainless steel) and non-ferrous tubes (copper, brass, plastic, etc.) and for final 'finishing' of tubes.

 
Stainless Steel Brushes
Used for removing soft and light scale deposits in ferrous tubes (carbon steel, stainless steel, etc.)

 
Brass Brushes
Used for removing soft and light scale deposits in straight, non-ferrous tubes (copper, brass, nickel and their alloyed tubes).

Brush O.D. Nylon 
Brush
 
Stainless Steel
 
Brass 
Brush
 
Threading Coupling
inch mm
1/4 6.4 N - 250 SS - 250 B - 250 8 - 32F P-1 (8 - 32M x 8 - 32M)
5/16 7.9 N - 312 SS - 312 B - 312 8 - 32F P-1 (8 - 32M x 8 - 32M)
3/8 9.5 N - 375 SS - 375 B - 375 12 - 24F P-2 (8 - 32M x 12 - 24M)
7/16 11.1 N - 437 SS - 437 B - 437 1/4 - 28M -
1/2 12.7 N - 500 SS - 500 B - 500 1/4 - 28M -
9/16 14.3 N - 562 SS - 562 B - 562 1/4 - 28M -
5/8 15.9 N - 625 SS - 625 B - 625 1/4 - 28M -
11/16 17.5 N - 687 SS - 687 B - 687 1/4 - 28M -
3/4 19.1 N - 750 SS - 750 B - 750 1/4 - 28M -
13/16 20.6 N - 812 SS - 812 B - 812 1/4 - 28M -
7/8 22.2 N - 875 SS - 875 B - 875 1/4 - 28M -
15/16 23.8 N - 937 SS - 937 B - 937 1/4 - 28M -
1 25.4 N - 1000 SS - 1000 B - 1000 1/4 - 28M -
Brushes should be ordered so that Brush O.D. is marginally less than tube I.D., for it to easily enter tube with deposit.
 
Drill Tip Double Diameter Brushes

         
Drill Tip Nylon Brush                               Drill Tip Brass Brush

These Brushes are used to clean internally grooved tubes. The drill tip of brushes cleans through hard scale before the brush cleaning action takes over. The large diameter of this brush cleans into the grooves of the tubes and the small diameter into the lands of the tube's rifling.

Tube I.D. Drill Tip
Nylon Brush
Drill Tip
Brass Brush
inch mm
5/8 15.9 DTBN-625  DTBB-625 
 

Brushes  1" & UP I.D.

Nylon Brushes
Recommended for removing soft scales in straight, non-ferrous tubes (copper, brass, plastic, etc.) and ferrous (stainless steel, carbon steel) and for final 'finishing' of tubes. Order brush so that brush O.D. is marginally smaller than tube I.D.

 

Stainless Steel Brushes
Recommended for removing soft and light scale deposits in straight, non-ferrous tubes. (carbon steel, stainless steel, etc.) Order brush so that brush O.D. is marginally smaller than tube I.D.

 

Brass Brushes
Recommended for removing soft and light scale deposits in straight, non-ferrous tubes. Order brush so that brush O.D. is marginally smaller than tube I.D.

Brush O.D. Nylon Brush Brass Brush Stainless
Steel
inch mm
1.1/4 31.7 N-1250 B-1250 SS-1250
1.1/2 38.1 N-1500 B-1500 SS-1500
1.3/4 44.5 N-1750 B-1750 SS-1750
2 51.0 N-2000 B-2000 SS-2000
2.1/4 57.1 N-2250 B-2250 SS-2250
2.1/2 63.5 N-2500 B-2500 SS-2500
2.3/4 70.0 N-2750 B-2750 SS-2750
3 76.2 N-3000 B-3000 SS-3000
3.1/4 82.6 N-3250 B-3250 SS-3250
3.1/2 89.0 N-3500 B-3500 SS-3500
3.3/4 95.2 N-3750 B-3750 SS-3750
4 101.6 N-4000 B-4000 SS-4000
 

Carbon Steel Brushes
Recommended for removing soft and light scale deposits in straight, ferrous tubes. Order brush so that brush O.D. is marginally smaller than tube I.D.

 

Plastic Brushes
Recommended for removing soft deposits in straight, ferrous and non-ferrous tubes and for final 'Finishing' up of cleaning in hoses, tubes and pipes. Order brush so that brush O.D. is marginally smaller than tube I.D.

 
Drill Tip Double Diameter Brushes

         
Drill Tip Nylon Brush                               Drill Tip Brass Brush

These Brushes are used to clean internally grooved tubes. The drill tip of brushes cleans through hard scale before the brush cleaning action takes over. The large diameter of this brush cleans into the grooves of the tubes and the small diameter into the lands of the tube's rifling.

Tube I.D. Drill Tip
Nylon Brush
Drill Tip
Brass Brush
inch mm
1 25.4 DTBN-1000 DTBB-1000
1.1/4 31.7 DTBN-1250 DTBB-1250

Note : Brushes over 1" O.D require # TCB-C Coupling to Connect to PFS-750, PFS-875 and PFS-875-SS shafts (One coupling is supplied with each brush order.)

.
 

 


Copyright 2003. Powermaster Engineers Pvt. Ltd.